Products 1-9 of 9
Show
BSI IC-2000 Rubber-Tough CA 1/2oz
Price: $4.99
View
Availability: Discontinued
Item #: BSI117 -

This is a half ounce bottle of Bob Smith Industries IC-2000™ Rubber-Toughened CA Glue. IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds,...

BSI Maxi-Cure Extra Thick CA 1/1oz
Price: $3.99
View
Availability: Discontinued
Item #: BSI111 -

MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.0-BSI111

BSI Insta-Set CA Accelerator 2oz
Price: $5.99
View
Availability: Discontinued
Item #: BSI151 -

This is 2oz bottle of INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.FEATURES: Formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strengthWill not craze most plastics even clear plastic and white foam. Forces the immediate cure of all cyanoacrylates Expands gap filling ability Permits structural fillet forming Solves most...

BSI Un-Cure CA Debonder 1oz
Price: $3.99
View
Availability: Discontinued
Item #: BSI161 -

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics...

BSI Quik-Cure 5 Min Epoxy 4.5oz
Price: $11.99
View
Availability: Discontinued
Item #: BSI201 -

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™...

BSI Mid-Cure 15 Min Epoxy 9oz
Price: $15.99
View
Availability: Discontinued
Item #: BSI204 -

MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.0-BSI204

BSI Slow-Cure 30 Min Epoxy 4.5oz
Price: $9.99
View
Availability: Discontinued
Item #: BSI205 -

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength...

IC-LOC High Strength Thread Locker Red
Price: $5.99
View
Availability: Discontinued
Item #: BSI-173H -

IC-LOC™ Red is a medium thickness, high strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Red™ is cured, the fasteners are permanently together and cannot be disassembled. IC-LOC Red™ will maintain its strength up to 490° F.0-BSI-173H

Foam Cure EPP Foam Glue 4oz
Price: $8.99
View
Availability: Discontinued
Item #: BSI142H -

FOAM-CURE is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it's curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE will act like a contact cement when...