LEDs

Give your rig a scale look with our LED Light Bar. This versatile setup works with 4V to 12V DC input and includes all the mounting hardware need for most 1/10 scale trucks. Perfect for off-road trucks or rock crawlers.Length: 0.8 in. ( 20.6 mm)Width: 4.6 in. (117.5 mm)Height: 1.2 in. (30.2 mm)Weight: 0.05 lbsNumber of LEDs: 5LED Size: 5 mmLED Housing Diameter: 0.9 in. (22.2 mm)LED Lead Length: 15 in. (381 mm)Connector Type: mCP XKit INCLUDES1 x Light Bar2 x Body Mounts1 x 5mm LED Set5 x Spot...

0-LIGHTTUBE-3MM-20-WHITE

0-LED-RGBCON-1

This 8-inch adapter cord is the easiest way to power the Self-Adhesive LED Light Strips. Just solder the leads to the positive and negative terminals on the LED strip, then plug the adapter into the balance connector of your 3-cell LiPo battery. In this way, you can use the same battery that's powering your motor to power up your LEDs.This adapter uses the JST-XH balance connector.0-LED-LEAD-8

For use with the E-Flite Universal Light Kit Controller.0-EFLA603

0-ram19

For use with the E-Flite Universal Light Kit Controller.0-EFLA602

0-LED-DFC-RGB

LED Lights - Up to 16 E-flite Universal light Kit LED's can be used on one controllerInput Voltage: 3-5.5 voltsDo not exceed 5.5 volts as this will damage your controllerOn - Off can be operated by a channel on your receiverOn -Off occurs at approximately middle stick positionOn at > 1.5ms - Off at Average Current Load6 LEDs - 60mA @ 5.5 volts12 LEDs - 120mA @ 5.5 volts16 LEDs - 160mA @5.5 volts 0-EFLA600

Responds to your transmitter! This easy-to-use, ultra-bright LED kit features 8 flashing modes that you can switch using any switched channel on your transmitter. It simulates a realistic aircraft lighting setup. Includes(5) White Lights - 5mm(2) Red Lights - 5mm(1) Green Light - 5mmSpecsInput Voltage: 4v-6vCurrent: 100mAMain Control Board Size: 30 x 30 x 10mmLED lead length: 800mm/pcWeight: 30g0-LEDKIT-2A

Red LED Flashing (2): Universal Light Kit0-EFLA607

EasyLights are an attractive, easy to use lighting system for your R/C vehicle. Just plug the light into a spare receiver channel, or use a separate 5V source.EasyLights each have a pair of ultra bright 10,000mcd white LEDs. The lights can be switched on and off by using your radio. If no signal is present or the signal wire is cut, the lights will default to being on.ApplicationsModel plane landing lightsModel car headlightsModel helicopter searchlightsBlinding your enemies SpecsInput...

Extensions for the Universal Light Kit.0-EFLA614

Extensions for the Universal Light Kit.0-EFLA613

This LED kit will give your 1/18 to 1/10-scale car or truck a truly unique look. The kit includes a control box and 12 LEDs in four different colors - white, yellow, blue and red. A simple push-button switch toggles between four different flashing patterns for the LEDs. All of the LEDs come with pre-installed 14 inch leads and connectors, so they can be mounted in almost any place on your car or truck. Best of all, the control box plugs directly into your receiver, so you won't need a separate...

For use with the E-Flite Universal Light Kit Controller.0-EFLA604

This is the White and Red LED Light Set from HPI.FEATURESDesigned for HPI 1/10 scale drift carsWhite LEDs for the headlights, red LEDs for the tail lightsFourteen different modes control the lighting effects from non-flashing for night driving to strobe flashing for custom driftlooksUses standard battery and receiver plugsINCLUDESTwo each Head and Tail Lights, Power Connector and Control UnitREQUIREMENTSAluminum tape, to attach lights and wiring to bodySPECIFICATIONSLED Wire Length: 14.5"...

These LED lights plug into the Lipo Fuel Gauge. They help give your plane a realistic look and make it easier to see during night flying.Comes with a set of three lights (green, blue and white) on separate 16" long wires.0-LS4FGAUGE

For use with the E-Flite Universal Light Kit Controller.0-EFLA606

This is a set of Quad Lites from Ram for the Helimax 1SQ Quadcopter.FEATURESLight weight, weighs only 0.705oz (2g)Two white LED headlights, and red and green flashing tail LEDs helpto keep heli oriented properlyEasy plug and play installationLow battery drainINCLUDESHead and tail lights with wiring and instructionsSPECIFICATIONSWire Length: 3.75" (95mm)0-RAME0191

0-RAM161

This is a Navigation Light System for Large Scale AirPlanes.0-RAM14

0-RAM132

FeaturesSix 3mm LEDsFor airplanes models with wingspans up to 54in. (1.37m)Ideal for night flying or low visibility conditionsLow battery drain (10mA in a 10 min flight)JST connectors for compatibility with most receivers and eliminates the need for extra channels or Y connectors ("plug and play" design)SpecsWeight: 0.28oz (8g)Wire Length: Navigation lights: 18in. (457.2mm)Landing and "strobe": 28in. (711.2mm)Requires a 6-12V battery0-RAM187 ...

This is the Ultra-Brite Adjustable Rate Strobe Light from RAM.FEATURESAdjustable rateHigh Intensity bulbPre-assembledINCLUDESOne connector for 9V batteryOne ON/OFF switchOne high-intensity bulbOne small circuit board with rate adjustment screwOne clear dome lensREQUIREMENTS9V batterySPECIFICATIONSWeight: 1oz.Wire Length: 35" of wire between circuit and strobeCircuit board-Length: 2"Width: 3/4"Height: 7/16"0-RAMQ0122 ...

This easy-to-use, ultra-bright LED kit simulates a realistic aircraft lighting setup. Each kit includes two red slow-blinking beacon lights, two white strobe lights, two white landing lights, and a one red and one green navigation light. With 600mm extensions, this kit will work for up to .60 size planes and helis.Includes(2) Red Beacon(2) White Strobe(2) White Landing Lights(1) Red Navigation Light(1) Green Navigation LightSpecsInput Voltage: 4v-6vCurrent: 30mAMain Control Board Size: 35 x 24...

For use with the E-Flite Universal Light Kit Controller.0-EFLA601

0-RNBRC7048Y3

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

The ShiftBrite is a module by macetech that integrates the Allegro A6281 3-channel constant current LED driver with a large, high-brightness RGB LED. Using just three digital output pins and a simple protocol, your microcontroller can control a long chain of ShiftBrites. Each ShiftBrite in the chain can be independently changed to any of the 1,073,741,824 possible colors to create dynamic displays and decorations. Adjustable current for each color channel lets you correct for slight...

Sinewinder is an attractive, easy to use lighting system for your R/C vehicle. Just plug the Sinewinder light into a spare receiver channel, or use a separate 5V source.Sinewinder has 12 bright LEDs that scan from side to side, with a short trail after the leading light. The lights can be switched on and off by using your radio. If no signal is present or the signal wire is cut, the lights will default to being on.Input Voltage: 3V to 6VCurrent Draw: 30mA max4"/10cm long0-SINE ...

This is a basic, general-purpose blue LED in a standard T1 (3mm) package with 0.1 in. lead spacing.Size: 3mmCurrent Rating: 30mAColor: BlueLens Type: Blue diffused0-PL1073

This is a basic, general-purpose green LED in a standard T1 (3mm) package with 0.1 in. lead spacing.Size: 3mmCurrent Rating: 25mAColor: GreenLens Type: Green diffused0-PL1071

This is a basic, general-purpose red LED in a standard T1 (3mm) package with 0.1 in. lead spacing.Size: 3mmCurrent Rating: 30mAColor: RedLens Type: Red diffused0-PL1070

This is a basic, general-purpose yellow LED in a standard T1 (3mm) package with 0.1 in. lead spacing.Size: 3mmCurrent Rating: 30mAColor: YellowLens Type: Yellow diffused0-PL1072

This multi-color LED contains red, green, and blue elements that can be mixed to produce any color. Unlike many other RGB LEDs, this unit has a diffused white lens that blends the colors without any additional diffusers or reflectors. This LED is sold individually.Size: 5mmCurrent Rating: 30mAColor: RGBLens Type: White diffusedPlease see the data sheet and detailed drawing for more information, located in the "Other Documantation" and "Alternate Pictures" tabs. 0-PL1074 Data Sheet ...

This adapter will let you power up to three separate Self-Adhesive LED Light Strips with a single 3S LiPo battery. You can even plug several of these adapters together and power an almost unlimited number of LEDs. Combine this with an 8-inch LED Light Strip Adapter and extension cords for a quick and easy wiring solution.This adapter uses the JST-XH balance connector.0-LED-MULTI-3X

0-ACEAQ0803-1

This LED light set is made for the Beacon but can easily fit any RC application. A very inexpensive way to add lighting to your vehicle.0-VNRF7927

Compatible with VEX 2.0 and VEX Pro Digital Outputs. Use these for feedback indicators, to debug code, verify Microcontroller mode, or for cool light patterns. Connect to the VEX Microcontroller Analog / Digital Ports when configured as a Digital Output. Set the line low to turn the LED On and set the line high to turn Off the LED. Inputs: +5VOutputs: GND(3) Red LED Indicators(3) Green LED Indicators(2) Yellow LED IndicatorsVEX-276-2176

These wheel LEDs give your drift car a flashy and unique look. They feature a hex pattern on the back that makes them quick and easy to pop in place between the wheel and the hub. They're powered by small button cell batteries that come included with the kit, so there are no wires to worry about. The LEDs are motion activated, so hit the throttle and GLOW!0-LED-WHEEL-BLU

These wheel LEDs give your drift car a flashy and unique look. They feature a hex pattern on the back that makes them quick and easy to pop in place between the wheel and the hub. They're powered by small button cell batteries that come included with the kit, so there are no wires to worry about. The LEDs are motion activated, so hit the throttle and GLOW!0-LED-WHEEL-GRN

These wheel LEDs give your drift car a flashy and unique look. They feature a hex pattern on the back that makes them quick and easy to pop in place between the wheel and the hub. They're powered by small button cell batteries that come included with the kit, so there are no wires to worry about. The LEDs are motion activated, so hit the throttle and GLOW!0-LED-WHEEL-ORG

These wheel LEDs give your drift car a flashy and unique look. They feature a hex pattern on the back that makes them quick and easy to pop in place between the wheel and the hub. They're powered by small button cell batteries that come included with the kit, so there are no wires to worry about. The LEDs are motion activated, so hit the throttle and GLOW!0-LED-WHEEL-RED

These wheel LEDs give your drift car a flashy and unique look. They feature a hex pattern on the back that makes them quick and easy to pop in place between the wheel and the hub. They're powered by small button cell batteries that come included with the kit, so there are no wires to worry about. The LEDs are motion activated, so hit the throttle and GLOW!0-LED-WHEEL-WHT

Y-Harnesses for the Universal Light Kit.0-EFLA616